12 Inch (300 mm) Borofloat 33 Wafers – Borofloat 33 (CTE 3.25 x 10^-6 /K, 350 nm – 2.0 um); 300 mm format, TTV <5 um. No minimum order; DFM review included with every RFQ.
A wafer is a specification bundle, not just a disc. 12 inch (300 mm) borofloat 33 wafers here mean SCHOTT float production, wafer grade material with certified CTE of 3.25 x 10^-6 /K, TTV controlled per format, and edges profiled for handler compatibility.
The numbers
| Material | Borofloat 33 (SCHOTT float production, wafer grade) |
|---|---|
| Thermal expansion (CTE) | 3.25 x 10^-6 /K |
| Service temperature | 450 C continuous |
| Transmission range | 350 nm – 2.0 um |
| Density | 2.23 g/cm3 |
| Knoop hardness | 480 kg/mm2 |
| Refractive index | 1.471 @ 587 nm |
| Stock thickness | 0.70 – 25.4 mm |
| Maximum blank size | 500 x 500 mm |
| Diameter / format | 300 mm |
| Thickness | 0.7 – 1.1 mm |
| TTV | <5 um |
| Flat / notch | SEMI notch |
| RFQ inputs | PDF/DXF/STEP drawing, quantity brackets, surface and edge spec |
DFM notes from the shop floor
Before sending the RFQ, check these against your drawing:
- Material note: float tin side must be tracked when parts see coating or bonding steps.
- Specify flat or notch orientation relative to your device layout – regrinding orientation later scraps the wafer.
- Over-specification is the quiet budget killer: a 20/10 scratch-dig face costs roughly three times an 80/50 face, so grade each surface individually.
The full rules live in our tolerance design guide and holes and edges design guide.
Process window
Beyond this page, Borofloat 33 routinely runs through lapping, coring, polishing, drilling in our shop – most real parts combine two or three of these steps.
Typical applications
12 inch (300 mm) borofloat 33 wafers shows up across mems devices (cap wafers, TGV substrates, motion-sensor lids); machine vision (camera windows, ring-light diffusers, calibration plates); led packaging (groove covers, phosphor carriers, package windows). Background reading on the underlying material science: SCHOTT BOROFLOAT product page.
The fastest route to a quote is geometry: use the 3D builder below, draw a dimensioned 2D drawing from it, or open the site-wide custom glass machining 3D + 2D builder for fully custom parts.
Engineers scoping this work usually also review wafer dicing process, Borofloat 33 selection guide, LED groove cover glass.
Buyer questions, answered
Do parts ship with inspection data?
Dimensional reports, surface certificates and material certs per melt are available; specify the level on the RFQ.
What tolerances are achievable on Borofloat 33 parts?
Ground features hold +/-0.01 mm and lapped thickness reaches +/-0.003 mm. Float tin side must be tracked when parts see coating or bonding steps.
What thickness range do you stock for Borofloat 33?
Standard stock spans 0.70 – 25.4 mm, with blanks up to 500 x 500 mm. Other formats are sourced per order.
How does Borofloat 33 behave under heat?
CTE is 3.25 x 10^-6 /K and continuous service reaches 450 C continuous, which is what drives its use where float-glass flatness off the line matters.
Is there a minimum order for 12 inch (300 mm) borofloat 33 wafers?
No. Single prototypes are accepted, and pricing steps down at 10, 100 and 1,000 pieces.
Specifications on this page were last reviewed by our engineering team in October 2026.